Yard-man 247.27432 Bedienungsanleitung

OPERATOR’S MANUALIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722PRINTED IN U.S.A.

10LIFT LEVERThe lift lever is used to change the operating position(height) of the cutting deck. To operate, move thelever to the left, then place in

11CRUISE CONTROL BUTTONThe cruise control button is located onthe tractor dash panel to the left of theignition switch. Push the cruise controlbutton

12SETTING THE CUTTING HEIGHTSelect the height position of the cutting deck byplacing the deck lift lever in any of the six differentcutting height not

13• While continuing to hold the cruise button in,lift your foot from the AutoDrive™pedal (youshould feel the cruise latch engage).• If properly engag

14• The operator must remain in the tractor seatat all times. If the operator should leave theseat without pushing the PTO knob inwardinto the disenga

15Side to SideIf the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed. Adjust ifnecessary as follows:WARNING: Tu

16Adjust the drag links so that equal lengths arethreaded into the ball joint on the left side and theball joint on the right side:• Loosen the jam nu

17SECTION 10: MAINTENANCEWARNING: Disconnect the spark plugwire(s) and ground against the enginebefore performing any adjustments, repairsor maintenan

18• Grasp the PTO idler pulley bracket and pivot ittoward the discharge chute to relieve tensionon the belt. Remove the deck belt from thebottom porti

19•RemovethedeckbeltfromtheelectricPTOclutchandfromaroundthePTOidlerpulley.•RoutethenewbeltasshowninFigure14,aroundthedeckpulleys,idlerpulleyandelectr

2SECTION 1: TABLE OF CONTENTSPAGEFINDINGYOURMODELNUMBER...2CALLINGCUSTOMERSUPPORT...

20Figure 16Upper Drive Belt• Locate the transmission idler pulley on the upper drive belt by looking through the battery tray opening.SeeFigure16.• Gr

21• Slide the belt off of the variable-speed pulleyas you lift the pulley up and out through thebattery tray opening.NOTE:Jacking the rear of the trac

22Thread the idler adjustment rod inward or outward tolengthen or shorten the travel of the double-idlerbracket until proper adjustment is achieved.•

23ChargingIf the unit has not been put into use for an extendedperiod of time, charge the battery with anautomotive-type 12-volt charger for a minimum

24SECTION 12: TROUBLESHOOTING GUIDETroublePossibleCause(s)Corrective ActionEngine willnot crankSafety switchbutton notdepressed.Battery installedincor

25

ÿþREF.NO.PARTNO. DESCRIPTION1 625-0051 Bulb/Socket Headlight Assembly725-1739 Bulb Only725-1649 Socket Only2 629-0928 Wiring Harness (Includes Ref 17)

27REF.NO.PARTNO. DESCRIPTION1 710-0788 Self Tapping Screw, 1/4-20 x 1.02 710-0599 Self Tapping Screw, 1/4-20 x .53 710-0751 Hex Cap Screw, 1/4-20 x .6

28Model 604493946645454137434236474844163028353238332731345051112829148139172122102012232122246281418251945316411697171551981466

29REF.NO.PARTNO. DESCRIPTION1 647-0040 Deck Stabilizer Rod2 683-0197 Lift Shaft Assembly3 711-0332 Clevis Pin, .5 x .784 712-0206 Hex Nut, 1/2-135 712

3SECTION 4: IMPORTANT SAFE OPERATION PRACTICESWARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IFNOT FOLLOWED, COULD ENDANGER THE

30Model 60412225396388101213111314151617181921202220242342526272829333131302932353430323536333940114142137434244444537

31REF.NO.PARTNO. DESCRIPTION1 683-0263 Lower Frame Assembly2 710-0604 Self-tapping Screw, 16-18 x .6253 783-0726 RH Pivot Support Bracket4 783-0727 LH

32Model 6044221351122212211319131836112831738464740844431243123747151719195026272410491933233032204214391661391376621369535425415758192364687371705865

33REF.NO.PARTNO. DESCRIPTION1 17839 Shift Lever Bracket2 17840 Transaxle Mounting Bracket3 618-0386 Single-speed Transmission Assembly4 631-0009 Shift

34Model 604412313101415161718191067896115125202852324251293037363835343332311272621223940

35NOTE:Forpaintedparts,pleaserefertothelistofcolorcodesbelow.Pleaseaddthe applicable color code, whereverneeded,tothepartnumbertoorderareplacement

36Model 60442-inch Deck46-inch Deck5111713171130373031861912262529522253555036192625292332202332212791873528261524161423418333381031010101740111342171

37REF.NO.PARTNO. DESCRIPTION1 17982 Reinforcement Spindle Plate2 618-0240 Spindle Assembly, 5 Dia.756-0959 Pulley Only3 618-0241 Double Pulley Spindle

38Model 604KohlerBriggs & StrattonIntek TwinSingle-cylinder9711(for choke)1349711(for choke)13912(for throttle)69221819208101410510516151(deflecto

39Engine AccessoriesREF.NO.PARTNO. DESCRIPTION1 710-0148 Self Tapping Screw, #8-32 x .3752 710-0599 Self Tapping Screw, 1/4-20 x .53 710-0604 Self Tap

4• Disengage all attachment clutches, thoroughlydepress the brake pedal, and shift into neutralbefore attempting to start engine.• Your mower is desig

MANUFACTURER’S LIMITED WARRANTY FOR:For TWO YEARS from the date of retail purchasewithin the United States of America, its possessionsand territories,

5• Keep all nuts, bolts and screws tight to be sure theequipment is in safe working condition.• Never tamper with safety devices. Check theirproper op

6Slope Gauge15°SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREEA POWER POLEA CORNER OF A BUILDINGOR A FENCE POSTFOLDONDOTTED LINE, REPRESENTINGA15°SLOPE

7SECTION 5: ATTACHMENTS & ACCESSORIESSECTION 6: TRACTOR SET-UPATTACHING THE BATTERY CABLESNOTE:The positive battery terminal is markedPos. (+). Th

8SECTION 7: CONTROLSFigure 3A Ignition Switch H Brake PedalB Throttle Control Lever I Parking Brake ButtonC PTO (Power Take-Off) Knob J Shift LeverD I

9IGNITION SWITCHTo start the engine, insert key into the ignition switchandturnclockwisetotheSTART position. Releasekey to the ON position once engine