OPERATOR’S MANUALIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722PRINTED IN U.S.A.
10ELECTRIC PTO (POWER TAKE-OFF) KNOB To engage the power to the cuttingdeck or other attachments, pulloutward on the PTO knob. Push thePTO knob inwar
11SHIFT LEVER The shift lever is locatedon the left side of thefender and has threepositions, FORWARD,NEUTRAL and REVERSE.The brake pedal must bedepr
12SETTING THE CUTTING HEIGHTSelect the height position of the cutting deck byplacing the deck lift lever in any of the six differentcutting height no
13• While continuing to hold the cruise button in,lift your foot from the AutoDrive™ pedal (youshould feel the cruise latch engage).• If properly eng
14• The operator must remain in the tractor seatat all times. If the operator should leave theseat without pushing the PTO knob inwardinto the diseng
15• With the tractor parked on a firm, levelsurface, place the lift lever in the top notch(highest position) and rotate the blade nearestthe discharg
16SEAT ADJUSTMENTTo adjust the position of the seat, move the seatadjustment lever (located under the seat) to the leftand slide the seat forward or
17• Loosen, but do NOT remove, the hex nutfound on the right side of the brake assembly.See Figure 12.• Using a feeler gauge, set the gap between the
18CLEANING THE ENGINE AND DECKAny fuel or oil spilled on the machine should bewiped off promptly. Do NOT allow grass, leaves, anddirt to accumulate a
19CHANGING THE DECK BELT(S)All belts on your tractor are subject to wear and should be replaced if any signs of cracking, shredding orrotting are pre
2SECTION 1: TABLE OF CONTENTSPAGEFINDING YOUR MODEL NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20Figure 16 CHANGING THE TRANSMISSION DRIVE BELT(S)All belts on your tractor are subject to wear and should be replaced if any signs of cracking, sh
21Figure 17 Lower Drive BeltNOTE: Proper removal of the lower drive beltrequires the removal of several tractor components.Read through the followi
22• Remove the hex bolt from the center of theengine pulley (or the electric PTO clutch onunits so equipped) and gently lower it off ofthe engine cra
23NOTE: The hex flange nut has a right-handed(normal) thread pattern. Do NOT attempt to force thenut in the incorrect direction. Doing so may damage
24SECTION 11: LUBRICATIONWARNING: Always stop the engine and disconnect the spark plug wire(s) and ground against the engine before performing any m
25SECTION 12: TROUBLESHOOTING GUIDETroublePossible Cause(s)Corrective ActionEngine will not crankSafety switch button not depressed.Battery installe
264142110423240121621314622222222333134263523242825302942736204379938171881911934214239Model 6041519221941408
27Tractor BodyREF.NO.PARTNO. DESCRIPTION1 710-3015 Hex Cap Screw, 1/4-20 x .752 710-0599 Self-tapping Screw, 1/4-20 x .53 712-3006 Hex Nut, 1/4-204 7
28Model 604493946640454137434236474844163028353238332731345051112829148135217211020122321222462814182519653411697171551981466262853
29REF.NO.PARTNO. DESCRIPTION1 747-1130 Deck Stabilizer Rod2 683-0197 Lift Shaft Assembly3 711-0332 Clevis Pin, .5 x .784 712-0206 Hex Nut, 1/2-135 712
3SECTION 4: IMPORTANT SAFE OPERATION PRACTICESWARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IFNOT FOLLOWED, COULD ENDANGER TH
30Model 6041222539638810121311131415161718192120222024232526272837333131302932353430323536333739401141421374342224323544464529
31REF.NO.PARTNO. DESCRIPTION1 683-0304 Lower Frame Assembly2 710-0604A Self-tapping Screw, 16-18 x .6253 783-0726A RH Pivot Support Bracket4 783-0727
32Model 604422135221221131913183611283173846474084412374715171195026272410491923303220421439166139137662136953542541575819236468737170586556565833777
33REF.NO.PARTNO. DESCRIPTION1 783-1015 Shift Lever Support2 17840 Transaxle Mounting Bracket3 618-0307C Single-speed Transmission Assembly4 631-0009 S
34Model 604Units with 618-0307CTransmission ONLY3112*204029212225192631302827183938383931312c1581724232116712c1412c91012*4113731336323712*3412*1414621
35REF.NO.PARTNO. DESCRIPTION1 618-0318 Clutch Collar†2 710-0788 Self-tapping Screw, 1/4-20 x 1.03 711-1274 Drive Shaft4 711-1280 Counter Shaft5 713-04
36Model 6044123134214151618191151253928232425129303736353433323112128224167896171043238UnitsEquipped w/ Electric PTO535455565051482616454457235058605
37NOTE: For painted parts, please refer tothe list of color codes below. Please addthe applicable color code, whereverneeded, to the part number to o
38Model 60442-inch Deck46-inch Deck52494914145867756768565393029352523777419302935382127382231715547365156432555072155171765751‡575757171217155962622
39REF.NO.PARTNO. DESCRIPTION1 16606 Retainer Hook2 618-0324 Spindle Assembly, 5.75 Dia.3 683-0198B 42-inch Deck Shell4 683-0254 Deck Adjustment Bracke
4• Disengage all attachment clutches, thoroughlydepress the brake pedal, and shift into neutralbefore attempting to start engine.• Your mower is desi
40Model 604KohlerBriggs & StrattonIntek TwinSingle-cylinder9711(for choke)1349738(for choke)13912(for throttle)69221819208101410510516151(deflect
41Engine AccessoriesBriggs & StrattonIntek Single32181920REF.NO.PARTNO. DESCRIPTION1 710-0148 Self-tapping Screw, #8-32 x .3752 710-0599 Self-tapp
42Model 604REF.NO.PARTNO. DESCRIPTION1 625-0051 Bulb/Socket Headlight Assembly2 629-0939 Wiring Harness w/o Ref. 14 (units w/ Electric PTO)629-0944 W
43Notes
MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTDPRODUCTS INC (“MTD”) with respect to new merchandisepurchased
5• Keep all nuts, bolts and screws tight to be sure theequipment is in safe working condition.• Never tamper with safety devices. Check theirproper o
6Slope Gauge15°SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREEA POWER POLEA CORNER OF A BUILDINGOR A FENCE POSTFOLD ON DOTTED LINE, REPRESENTING A 15°
7SECTION 5: ATTACHMENTS & ACCESSORIESSECTION 6: TRACTOR SET-UPATTACHING THE BATTERY CABLESNOTE: The positive battery terminal is markedPos. (+
8SECTION 7: CONTROLSFigure 3 A Ignition Switch H Brake PedalB Throttle Control Lever I Parking Brake ButtonC Choke Control (if so equipped) J Shift
9IGNITION SWITCHTo start the engine, insert key into the ignition switchand turn clockwise to the START position. Releasekey to the ON position once
Kommentare zu diesen Handbüchern